Welding Rod Sizes and Amperage Chart
Welding rod size is the diameter of the metal core: 1/16, 3/32, 1/8 and 5/32 in are the common sizes. Match the size to the metal thickness and set the amps in the range on the rod box. For 1/8 in rods, 6013 runs at about 75 to 130 A and 7018 at about 90 to 160 A. Thicker rods need more amps and a stronger welder.
Rod size and amperage chart
| Rod diameter | 6013 amps | 7018 amps | Typical metal thickness |
|---|---|---|---|
| 1/16 in (1.6 mm) | About 20 to 40 A | Rarely made | Thin sheet |
| 3/32 in (2.4 mm) | About 40 to 90 A | About 70 to 110 A | Thin to medium plate |
| 1/8 in (3.2 mm) | About 75 to 130 A | About 90 to 160 A | The most common general size |
| 5/32 in (4.0 mm) | About 110 to 165 A | About 130 to 220 A | Thicker plate, flat and horizontal |
These are typical ranges that match the rod pages for 6013 and 7018. The rod maker prints a range on each box, and that range wins. Many rods are about 14 in long, though lengths vary.
How to pick the size
- Check the metal thickness. As a rough guide, use a rod core that is not much thicker than the metal.
- Check what your welder can supply. A small 120 V stick welder may top out near the 1/8 in range, so heavier rods need a bigger machine. See stick welders.
- Choose the rod type for the job, as in 6013 vs 7018.
How to set the amps
- Start in the middle of the maker’s range.
- Strike an arc on scrap of the same thickness and look at the bead. A bead that is narrow and piled up needs more current, and one that is flat with spatter or burn-through needs less.
- Raise or lower by 5 to 10 A and test again.
- Use lower amps for vertical and overhead welds, since the weld pool is harder to control.
Rod number
E6013 reads as electrode, 60,000 psi minimum tensile strength, all positions, and a titania flux that runs on AC or DC. The 7018 number has a low-hydrogen flux, so store that rod dry. For storage rules, see 7018 rod.
Safety
Wear a helmet with the right shade, gloves and a jacket, and weld in a ventilated place. See welding safety tips.
Frequently asked questions
What size welding rod should I use?
For thin sheet use 1/16 or 3/32 in. For general work and plate up to about 1/4 in, use 1/8 in. For thicker plate and flat welding, use 5/32 in or larger if your welder has the amps.
What amperage for a 1/8 in 6013 rod?
About 75 to 130 A. Start in the middle and adjust. Check the range on the rod box.
What amperage for a 1/8 in 7018 rod?
About 90 to 160 A, often 110 to 150 A. 7018 usually needs a little more current than 6013 at the same size.
What do the numbers on a welding rod mean?
In E6013, E means electrode, 60 is the minimum tensile strength in thousands of psi, the third digit is the welding positions (1 means all positions) and the last digit is the flux type.
Related guides
- Guide
Plug Weld vs Spot Weld: How to Make a Plug Weld
Plug weld vs spot weld: how each joins overlapping sheet, when to use a plug weld with a MIG welder, hole size, step by step, and how to check the result.
- Guide
Spot Weld Cutter: How to Drill Out Spot Welds
What a spot weld cutter is, how to drill out spot welds to remove a panel without bending it, which bits to use, and how to avoid cutting the lower sheet.
- Guide
Welding Boots and Caps: What to Wear Head to Toe
What to wear for welding from head to toe: leather boots, trousers over the boots, welding caps, gloves and jacket, and what to avoid so sparks stay out.