Oxy-Acetylene Torch: Setup, Flame Types and Safety
An oxy-acetylene torch burns acetylene in oxygen to give a flame hot enough to weld, braze, heat and cut steel. The setup is two cylinders with regulators, two hoses, flashback arrestors and a torch with the right tip. Set a neutral flame for welding, and never run acetylene above 15 psi. Follow the maker’s lighting and shutdown order.
Parts of an oxy-acetylene set
| Part | Job |
|---|---|
| Oxygen and acetylene cylinders | Store the gases; chain them upright |
| Regulators | Reduce cylinder pressure to working pressure |
| Hoses (green oxygen, red fuel gas) | Carry the gases to the torch |
| Flashback arrestors and check valves | Stop flame and reverse flow |
| Torch handle and tip | Mix the gases and form the flame |
| Welding or cutting attachment | Welding tip or cutting head |
Flame types
| Flame | Mix | Used for |
|---|---|---|
| Neutral | Equal oxygen and acetylene | Welding steel |
| Carburizing | Extra acetylene | Some hardfacing, light heating |
| Oxidizing | Extra oxygen | Brazing some metals, cutting |
A neutral flame has a clear, bright inner cone with no feather. Adjust slowly to see the feather disappear.
Setup in outline
- Secure the cylinders upright and remove the caps.
- Crack each cylinder valve briefly to blow out dirt, with no ignition nearby.
- Fit the regulators and hoses, and fit flashback arrestors as the maker specifies.
- Open the acetylene cylinder valve slowly, a quarter to half turn, so you can shut it fast. Open the oxygen valve fully.
- Set the working pressures from the tip chart.
- Leak test with soapy water. Never use oil or grease on any fitting.
- Light with a striker, never a lighter or match, then adjust the flame.
Follow the maker’s manual for exact lighting and shutdown order, as the details vary by torch.
Compared with other processes
Oxy-acetylene is slower to learn for welding than a wire-feed machine. See MIG welding, stick welders and types of welding for how the other processes compare.
Safety
Oxygen makes oil and grease burn violently, so keep them away from fittings. Store cylinders upright and chained, and away from heat. Use goggles with the right shade and wear gloves. See welding safety tips. Weld in a ventilated area with a fire extinguisher nearby.
Frequently asked questions
What is the difference between oxy-acetylene and MIG welding?
Oxy-acetylene is a gas flame used with filler rod. It can also heat and cut metal. MIG uses an electric arc and a wire feed. MIG is easier for most beginners to weld with.
What are the three oxy-acetylene flames?
Neutral (equal gas, used for welding steel), carburizing (extra acetylene, used for some hard-surfacing and soft metals) and oxidizing (extra oxygen, used for brazing some metals and cutting).
What pressure should acetylene be set to?
Never above 15 psi (about 1 bar). Above that, acetylene becomes unstable. Use the pressure the tip chart gives, which is usually well under 15 psi.
What is a flashback arrestor?
A safety device on the torch or regulator that stops a flame traveling back into the hoses and cylinders. Fit them as the maker advises.
Related guides
- Guide
Can You Weld Galvanized Steel? Fumes and Safe Method
Can you weld galvanized steel? Yes, but the zinc makes harmful fumes. How to grind off the coating, ventilate, protect yourself and weld it safely.
- Guide
Welder Generators: What Size Generator to Run a Welder
What size generator runs a welder: how to read the welder's input amps and volts, running vs surge watts, inverter generators and engine-driven welders.
- Guide
Welding Magnets: Types, Angles and Holding Force
Welding magnets compared: arrow, switchable and adjustable-angle types, 45, 90 and 135 degree holds, holding force ratings, heat limits and how to use them.