Welding Lens Shade Chart: Which Shade for Which Process
Welding lens shade is a number from 2 to 14: the higher the number, the darker the lens. Typical minimums are shade 10 for stick welding with small electrodes, 12 for stick with 3/16 to 1/4 in electrodes and for MIG on steel, 12 for TIG, and 14 for the largest stick electrodes. Gas welding uses shade 4 to 8 and cutting uses shade 3 to 6. These come from the filter lens table in OSHA 1910.133, and you may always choose a darker lens than the minimum.
Lens shade by process
| Process | Detail | Minimum shade |
|---|---|---|
| Stick (SMAW) | 1/16 to 5/32 in electrodes | 10 |
| Stick (SMAW) | 3/16 to 1/4 in electrodes | 12 |
| Stick (SMAW) | 5/16 to 3/8 in electrodes | 14 |
| MIG (GMAW) | Nonferrous metals | 11 |
| MIG (GMAW) | Ferrous metals (steel) | 12 |
| TIG (GTAW) | 1/16 to 5/32 in electrodes | 12 |
| Carbon arc welding | Not common in home shops | 14 |
| Gas welding | Light, under 1/8 in | 4 to 5 |
| Gas welding | Medium, 1/8 to 1/2 in | 5 to 6 |
| Gas welding | Heavy, over 1/2 in | 6 to 8 |
| Gas cutting | Light, medium and heavy | 3 to 4, 4 to 5, 5 to 6 |
| Torch brazing | 3 to 4 |
Welding standards also give amperage-based charts, and manufacturers print their own in the manual, so follow the chart that comes with your helmet.
Shade 14 and shade 10
Shade 14 is the darkest common lens. It suits bright arcs such as the largest stick electrodes, and you will see it listed as a fixed lens for passive helmets. Many auto-darkening lenses stop at shade 13, so check the range if you need 14. Shade 10 is the usual minimum for small stick work and a common fixed shade for passive helmets.
How to choose a shade
- Start from the process and the size of the electrode or the current in the table.
- If the arc looks uncomfortably bright, or you see spots afterward, go up a shade.
- If you cannot see the joint, go down a shade, but never below the minimum for the process.
- Use a variable lens, such as shade 9 to 13, so one helmet can cover most jobs; see welding helmets.
Welding glasses and goggles
Gas welding, brazing and cutting need a lens of shade 3 to 8, in goggles or glasses made for the job. Do not use these for arc welding. Wear safety glasses with side shields under the helmet. For the rest of the protective gear, see welding safety tips.
Frequently asked questions
What shade for MIG welding?
A minimum of shade 11 for nonferrous metals and 12 for steel is given in the OSHA filter lens table. Many welders work at about shade 10 to 13, moving up with higher current.
What shade do I need for stick welding?
Shade 10 for small electrodes (1/16 to 5/32 in), 12 for 3/16 to 1/4 in, and 14 for 5/16 to 3/8 in electrodes.
Is shade 14 too dark?
For small welds yes, because you cannot see the joint. Shade 14 is for very bright arcs such as the largest stick electrodes and carbon arc work.
Can I wear shade 5 glasses for arc welding?
No. Shade 5 is for gas welding and light cutting. Arc welding needs a much darker lens, normally shade 10 or higher.
Related guides
- Guide
Welding Cable Size Chart: 2 AWG, 1/0, 2/0 and 4/0
Welding cable sizes in AWG compared by amperage and length: when to use 2 AWG, 1/0, 2/0 or 4/0 cable, copper vs aluminum, and how to pick leads for your welder.
- Guide
Flux Core vs MIG Welding: Which Wire and Setup to Use
Flux core vs MIG: how each works, gas and no-gas wire, polarity, what each welds best, spatter, wind and thin metal, and which a home welder should choose.
- Guide
6013 Welding Rod: Uses, Amperage and 6013 vs 7018
What E6013 means, what the rod welds best, amperage by rod size, how it compares with 6011 and 7018, and how to run it on an AC or DC stick welder.