Welding Cable Size Chart: 2 AWG, 1/0, 2/0 and 4/0
Welding cable is sized in AWG, and a smaller number means a thicker cable. As a typical guide, 2 AWG carries about 150 to 200 A on short leads, 1/0 about 200 to 300 A, 2/0 about 250 to 350 A and 4/0 400 A and up. Use the next size up for long leads, because voltage drop and heat rise with length. These figures are typical, so follow the cable size in your welder’s manual.
Welding cable sizes at a glance
| Cable size | Typical current (short leads) | Typical use |
|---|---|---|
| 6 or 4 AWG | Up to about 100 to 150 A | Small home machines, short leads |
| 2 AWG | About 150 to 200 A | Home stick and MIG welders |
| 1/0 | About 200 to 300 A | Heavier home and farm welders |
| 2/0 | About 250 to 350 A | Shop machines, longer leads |
| 3/0 and 4/0 | 350 to 400 A and up | Industrial welding, long runs |
Makers and cable suppliers publish their own charts, and the safe current also depends on duty cycle, ambient temperature and the insulation rating. When the table and your welder’s manual disagree, use the manual.
How AWG sizes work
AWG numbers run backwards: 6 AWG is thinner than 4 AWG, which is thinner than 2 AWG. The next size past 1 AWG is 1/0 (one-aught), then 2/0, 3/0 and 4/0, and each step is thicker. That is why 2/0 is a much heavier cable than 2 AWG, even though the numbers look alike.
How cable length changes the size
The cable carries the current out to the work and back through the ground lead, so the electrical length is about twice the distance to the work. A long cable has more resistance, which drops voltage, heats the cable and weakens the arc. Move up one size for leads longer than about 50 ft, and use the shortest leads that reach the job.
What to look for in welding cable
- Copper conductor, with many fine strands so the cable stays flexible.
- A flexible insulation rated for welding, such as EPDM or neoprene, that resists heat, oil and abrasion.
- A voltage rating of at least 600 V.
- Clean, tight lugs and connectors rated for the cable size. A loose connector heats up more than the cable does.
Connectors, clamps and holders
The electrode holder and ground clamp must be rated for the machine’s current. Many machines use Dinse-style connectors, so match the connector to the machine and the cable size. Crimp or solder lugs properly and cover them with heat-shrink or insulation.
Safety
Check cable for cracked insulation, exposed copper, loose lugs and hot spots. A cable or connector that gets hot during welding is too small, too long or loose. Replace damaged cable, keep leads off wet ground and away from sharp edges, and read welding safety tips.
For machine amperage ranges, see stick welders and 7018 welding rod amperage, and for what else to buy for a home shop, see welding tools for a home shop.
Frequently asked questions
What size welding cable do I need for 200 amps?
Typically 1/0 for leads of about 50 ft or less at moderate duty cycle, and 2/0 for longer runs or heavy use. The welder's manual gives the cable size for its rated output.
Is a bigger welding cable better?
Thicker cable drops less voltage and runs cooler, but it costs more and is stiffer. Match the size to the current and the length, and don't go smaller than the maker recommends.
Is 2/0 welding cable the same as 2 AWG?
No. 2/0 (pronounced two-aught) is much thicker than 2 AWG. The aught sizes 1/0, 2/0, 3/0 and 4/0 are larger than 1 AWG.
Can I use copper or aluminum welding cable?
Copper is the standard because it carries more current for its size and holds up to flexing and connectors. Aluminum cable needs a larger size for the same current and is not common for welding leads.
Related guides
- Guide
Welding Lens Shade Chart: Which Shade for Which Process
Welding lens shade numbers by process and electrode size, from shade 3 for cutting to shade 14 for heavy stick welding, and how to choose a lens.
- Guide
Flux Core vs MIG Welding: Which Wire and Setup to Use
Flux core vs MIG: how each works, gas and no-gas wire, polarity, what each welds best, spatter, wind and thin metal, and which a home welder should choose.
- Guide
6013 Welding Rod: Uses, Amperage and 6013 vs 7018
What E6013 means, what the rod welds best, amperage by rod size, how it compares with 6011 and 7018, and how to run it on an AC or DC stick welder.