Chop Saw vs Table Saw: Differences and Combo Setups
A chop saw (miter saw) makes crosscuts and angled cuts by lowering a blade onto a board held against a fence, and a table saw makes rip cuts and sheet cuts by pushing the board over a fixed blade. Buy the chop saw first for trim, framing and decks, and the table saw first if you mostly rip boards and plywood. A combo setup uses both on one stand or workbench.
Chop saw vs table saw at a glance
| Chop saw (miter saw) | Table saw | |
|---|---|---|
| Main cut | Crosscut and miter | Rip and crosscut with a sled |
| How it works | Blade comes down onto the board | Board is pushed over the blade |
| Best for | Trim, framing, decks, repeat cuts to length | Ripping lumber, plywood, dados |
| Cuts angles | Easily, miter and bevel | With a miter gauge or sled |
| Typical blade | 10 or 12 in | 10 in |
| Footprint | Smaller | Larger |
| Safety focus | Hands clear of the blade path | Kickback, so use a push stick |
Which should you buy first?
- If your jobs are trim, framing, decks and fences, buy a miter saw. It gives fast, accurate crosscuts and angles with little setup.
- If you cut plywood, build cabinets or rip boards to width, buy a table saw.
- If you do both, get the miter saw first, because a circular saw with a guide can stand in for some table saw jobs, but not for repeated accurate crosscuts.
A radial arm saw sits between the two; see radial arm saw vs miter saw, and sliding vs non-sliding miter saws for how a miter saw cuts wider boards.
What “chop saw” means
Chop saw has two meanings. In a woodshop it is a miter saw. In a metal shop it is an abrasive or cold-cut saw for steel, covered in best saw for cutting metal. The two use different blades, so do not put a wood blade on a metal saw. Blades are covered in saw blade types.
Chop saw and table saw combo setups
A combo setup puts both saws in a small space:
- A miter saw station beside the table saw, using the table saw’s outfeed table as the miter saw’s support.
- A shared bench with the miter saw at one end and the table saw at the same height, so long boards run across both.
- A wheeled stand so one saw can be stored away.
Align the miter saw fence to the table saw top so long boards stay supported, and square the table saw fence before you rip; see how to square a table saw fence.
Safety
Keep your hands clear of the blade path, use a push stick or push block on the table saw, wear eye and ear protection, and unplug the saw to change a blade. Follow the maker’s manual for blade size and guards.
Frequently asked questions
Is a chop saw the same as a miter saw?
In many shops, yes: a chop saw is a miter saw. The word also names the abrasive metal-cutting chop saw. Check which type is meant before you buy.
Which is more useful, a miter saw or a table saw?
A miter saw is more useful for trim, framing and decks, because it makes fast, accurate crosscuts and angles. A table saw is more useful for ripping lumber to width and cutting sheet goods.
Can a miter saw replace a table saw?
Not for ripping. A miter saw cannot cut a board along its length, or cut a full sheet of plywood. For that, use a table saw, or a circular saw with a guide.
Is there a combination chop saw and table saw?
Machines that combine the two exist, but they are a compromise. Most people use a miter saw and a table saw on a shared stand or against a workbench.
Related guides
- Guide
Dovetail Saw: TPI, Rip vs Crosscut Teeth
Dovetail saw explained: the fine backsaw for cutting dovetails, typical 14 to 20 TPI, rip vs crosscut teeth, blade length and how to saw to a line.
- Guide
Panel Saw: Hand Panel Saw vs Vertical Panel Saw
Panel saw explained: the hand panel saw with rip or crosscut teeth, the vertical panel saw for plywood sheets, how they differ, sizes, TPI and which to buy.
- Guide
Reciprocating Saw Blades: TPI, Length and Which to Use
How to choose a reciprocating saw blade by material: TPI for wood, nailed wood, metal and pruning, blade length, bi-metal vs carbide, and cutting tips.