All guides
- Guide
Drill Bit Size for a #10 Screw: Pilot and Clearance Holes
Drill bit sizes for #10 screws: 1/8" pilot in softwood, 9/64" in hardwood, 3/16" clearance, plus tap drills for 10-24 and 10-32 threads.
- Guide
Drill Bit Sets: Which Set for Wood, Metal and Masonry
How to choose a drill bit set: HSS, cobalt, titanium-coated, brad point and masonry sets compared, which sizes a set should include, and what to avoid.
- Guide
Drill Bit Size Chart: Fractional, Number, Letter and Metric
Drill bit size chart with fractional, number, letter and metric drills in decimal inches and mm, plus how to measure a bit. Tap drill sizes have their own chart.
- Best picks
Best Drill Bits for Stainless Steel: Cobalt and Step Bits
Drill bits for stainless steel: M35 and M42 cobalt, step bits, the speed and oil to use, and eight bits and sets compared.
- Guide
Tap Drill Size Chart: UNC, UNF, Metric and NPT
Tap drill sizes for UNC, UNF, metric and NPT threads in one chart, with decimal inches and millimetres, and how to pick the right drill for each tap.
- Guide
Can You Drill Tempered Glass? Why It Shatters
No, tempered glass can't be drilled: it shatters as soon as the surface is cut through. How to tell if glass is tempered, and how to drill ordinary glass.
- Guide
Can You Drill Into Wood Filler? When and How
Yes, you can drill into most wood fillers once fully cured. Which fillers hold screws, how long to wait, and how to drill without cracking the patch.
- Guide
1/2 in vs 3/8 in Drill: Which Chuck Size Do You Need?
1/2-inch vs 3/8-inch drill: what the chuck size means, the largest bit each takes, torque and weight, and which suits DIY or heavy-duty work.
- Guide
Drill Guides and Drill Press Stands for a Hand Drill
How a drill guide or drill press stand helps a hand drill make straight, square and angled holes, which type to choose, and when you need a real drill press.
- Guide
Can a Hammer Drill Be Used as a Regular Drill?
Yes, a hammer drill works as a regular drill with the hammer action switched off. When it's a good substitute, when it isn't, and how to set it.
- Guide
Can You Use a Hammer Drill to Mix Concrete?
You can mix small batches of concrete or mortar with a hammer drill in drill-only mode and a paddle. Speed, paddle size, and when to use a mixer.
- Guide
How to Reduce Drilling Noise at Home
How to make drilling quieter: the right drill and bit, sharp bits and lower speed, damping vibration, timing, and hearing protection.
- Best picks
Best Cordless Drills for Polishing, With Buffing Pads
Cordless drills and buffing pad kits for polishing cars and furniture: speed control, chuck size and pad choice, with four drills and two pad sets.
- Guide
Can a Drill Press Be Used as a Mill?
A drill press can do only very light milling, because its chuck and bearings aren't made for side loads. The risks, what works, and when to buy a mill.
- Guide
Self-Drilling vs Self-Tapping Screws: Which Do You Need?
Self-drilling screws drill their own hole and cut threads in one step; self-tapping screws need a pilot hole. Which to use for metal, wood and roofing.
- Guide
What Do the Numbers on a Drill Mean? Clutch and Speed
What the numbers on a drill mean: the clutch (torque) ring, the 1 and 2 speed switch, the drill and hammer symbols, and which setting to use.
- Guide
Types of Hammers: Framing, Dead Blow, Ball Peen and Mallet
Types of hammers and their uses: claw, framing, finishing, ball peen, dead blow, mallet, sledge and drywall hammers, with weights and which to buy first.
- Guide
Can I Use a Torque Wrench as a Breaker Bar?
Why you shouldn't use a torque wrench as a breaker bar to loosen tight bolts, what it does to its calibration, and what to use instead.
- Guide
Types of Torque Wrenches: Click, Digital and Beam
Torque wrench types compared: click, beam, dial, digital and split-beam, which drive size (1/4, 3/8 or 1/2 in) suits which job, accuracy and use.
- Guide
Can You Use 21 Degree Nails in a 22 Degree Nailer?
Whether 21-degree nails work in a 22-degree framing nailer: why many nailers accept a range of angles, when it jams, and what to check first.
- Guide
What Is a Palm Nailer and When to Use One?
What a palm nailer is, how it works, the jobs it suits (joist hangers, tight spaces, short and full-size nails), air vs cordless, and how to use one safely.
- Guide
Brad Nailer vs Finish Nailer vs Pin Nailer
Brad, finish and pin nailers compared: nail gauge, nail length, holding power and the jobs each one suits, plus where framing nailers and staplers fit in.
- Guide
Can You Use Used Motor Oil for Chainsaw Bar Oil?
Why used motor oil makes poor chainsaw bar oil: it lacks tackifier, carries metal and soot, and can void the warranty. Better alternatives listed.
- Guide
16 vs 18 Inch Chainsaw: Which Bar Length Do You Need?
16 vs 18 inch chainsaw bars compared: wood size each cuts, engine size, weight, control and safety, and the simple rule for choosing a bar length.
- Best picks
Best Aftermarket Chainsaw Carburetors and How to Choose
Aftermarket chainsaw carburetors compared: which fit Stihl, Husqvarna and Poulan saws, what the kits include, and how to choose and fit one.
- Guide
How to Measure a Chainsaw Bar and Chain
How to measure a chainsaw bar (called length vs true length) and find the chain's pitch, gauge and drive link count, so a replacement bar or chain fits.
- Guide
Can I Cut Aluminum With a Chop Saw?
Yes, a chop saw cuts aluminum with a carbide blade made for non-ferrous metal. Which blade, how to set up the cut, and the safety steps.
- Guide
Can a Wood Bandsaw Cut Metal? Speed and Blades
A wood bandsaw runs too fast for most metal. Blade speeds compared, what a wood bandsaw can cut (aluminum, brass), and how to slow one down.
- Guide
Can You Cut Plexiglass With a Bandsaw?
Yes, a bandsaw cuts plexiglass with a fine-tooth blade and steady feed. Blade TPI, speed, how to stop melting and chipping, and safety tips.
- Guide
Are Circular Saw Blades Hardened?
Yes: circular saw blade plates are heat-treated, and carbide tips are far harder still. How blades are hardened and what it means for use and sharpening.