How to Read a Tape Measure: 5/8, 1/16 and Metric Marks
On an inch tape measure, each inch is split into 16 equal parts. The line lengths tell you which fraction you’re on: the longest line inside the inch is 1/2, the next longest are 1/4 and 3/4, then the eighths, and the shortest are sixteenths. 5/8 in is the fifth eighth, which is 10 sixteenths, just past the half-inch line. Most tapes also mark every 16 in in red, for stud spacing, and every 19.2 in with a black diamond, for joist layout.
The fractions within one inch
| Mark | Sixteenths | Decimal (in) | mm |
|---|---|---|---|
| 1/16 | 1 | 0.0625 | 1.6 |
| 1/8 | 2 | 0.125 | 3.2 |
| 3/16 | 3 | 0.1875 | 4.8 |
| 1/4 | 4 | 0.25 | 6.4 |
| 5/16 | 5 | 0.3125 | 7.9 |
| 3/8 | 6 | 0.375 | 9.5 |
| 7/16 | 7 | 0.4375 | 11.1 |
| 1/2 | 8 | 0.5 | 12.7 |
| 9/16 | 9 | 0.5625 | 14.3 |
| 5/8 | 10 | 0.625 | 15.9 |
| 11/16 | 11 | 0.6875 | 17.5 |
| 3/4 | 12 | 0.75 | 19.1 |
| 13/16 | 13 | 0.8125 | 20.6 |
| 7/8 | 14 | 0.875 | 22.2 |
| 15/16 | 15 | 0.9375 | 23.8 |
The same fractions name drill bits, wrenches and sockets, so this table doubles as a size converter. For the full list of drill sizes, including the number and letter drills between these fractions, see the drill bit size chart.
How to read a measurement
- Read the last whole inch before the end of what you’re measuring, for example 7 in.
- Count the lines past it to the end point. If it lands on the second-longest line after the half, that’s 3/4.
- Reduce the fraction: 10/16 is 5/8, 12/16 is 3/4, 4/16 is 1/4.
- Put them together: 7-5/8 in.
Some tapes mark the first 12 inches in 1/32 in for fine work. Count those lines carefully: they’re twice as dense.
Special marks: red numbers and black diamonds
- Red numbers or boxes every 16 in: standard spacing for wall studs, measured center to center.
- Black diamonds every 19.2 in: used for joists or trusses so five fit evenly across an 8 ft (96 in) sheet of plywood or OSB.
- Feet markings: many tapes print “1F”, “2F” and so on at each foot, or show feet and inches together (for example 2’ 7”).
Why the hook moves
The metal hook at the end slides by exactly its own thickness. When you hook it over an edge and pull, it slides out; when you push it against a wall, it slides in. Either way the zero point stays accurate. Don’t bend it or tighten its rivets.
Metric tapes
Metric tapes mark millimetres, with longer lines at each 5 mm and numbered centimetres. Read the last centimetre, then count the millimetres: 23 cm and 7 mm is 237 mm. Many tapes show inches on one edge and metric on the other.
Measuring for a cut
Mark measurements with a V (a small “crow’s foot”) pointing to the exact spot, and remember the saw blade removes material too: cut on the waste side of the line. For cutting framing lumber, see can a jigsaw cut a 2x4.
Frequently asked questions
Where is 5/8 on a tape measure?
Count past the half-inch line by one eighth (two sixteenth marks). 5/8 in equals 10/16 in, or 0.625 in (15.9 mm).
Why is the hook at the end of a tape loose?
On purpose. It slides by its own thickness, so the measurement is right whether you hook the tape over an edge (pull) or push it against a surface (push).
What are the black diamonds on a tape measure?
Marks every 19.2 inches, used to lay out joists or trusses so that five of them fit evenly across an 8 ft (96 in) sheet.
Related guides
- Guide
Parts of a Hammer and How to Replace a Handle
The parts of a hammer (head, face, claw, eye, handle and wedge) and how to replace a broken or loose handle on a claw hammer or sledgehammer.
- Guide
Types of Pliers and What Each One Is For
Pliers types compared: slip-joint, tongue-and-groove, needle-nose, locking, linesman and diagonal cutters, with typical sizes and what to use each for.
- Guide
Screwdriver Types and Sizes: Phillips, Slotted and Torx
Screwdriver tip types and sizes: Phillips PH1 to PH3, Pozidriv, slotted, Torx, square and hex, which one fits which screw, and how to avoid stripping.