Drill Attachments: Sander, Socket Adapter and Wire Brush
The drill attachments worth owning are sanding pads and drums, socket adapters, wire brushes, polishing pads, right-angle heads and paddle mixers. Each turns a drill into a simple version of another tool for occasional jobs. Before you use any of them, check that the attachment’s maximum speed rating is higher than your drill’s top speed, and fit the drill’s side handle if it has one: some attachments grab and twist hard.
Common drill attachments and their uses
| Attachment | What it does | Good for | Watch out for |
|---|---|---|---|
| Sanding disc on a backing pad | Hook-and-loop discs on a shank-mounted pad | Shaping, rust and paint spots, small surfaces | Leaves swirl marks; hard to keep flat |
| Sanding drum | Rubber drum with sanding sleeves | Curves, inside edges, holes | Use in a drill press for square edges |
| Flap wheel | Overlapping abrasive flaps | Smoothing, deburring metal | Wear eye protection |
| Socket adapter | Hex shank to 1/4, 3/8 or 1/2 in square drive | Driving nuts and lag bolts | Not for final torque; impact-rated only on impact drivers |
| Wire brush (cup or wheel) | Steel or brass wire | Rust, scale, loose paint | Wires fly off; goggles and gloves |
| Polishing pad | Foam or wool pad on a backing plate | Car paint, headlights, metal | Keep speed low to avoid burning paint |
| Right-angle attachment | Gearbox that turns the drive 90° | Drilling and driving between joists and studs | Adds length to the chuck side |
| Paddle mixer | Spiral or cage paddle | Paint, thinset, small batches of mortar | Needs a strong, slow drill; see below |
| Hole saw | Toothed cup with a pilot bit | Large holes in wood, plastic, thin metal | Slow speed; it can grab |
Sanding with a drill
A sanding disc in a drill is fine for small jobs: rounding an edge, smoothing a patch, taking rust off a bracket. For whole tabletops and cabinet doors it’s the wrong tool. The disc spins around a fixed center, so it leaves circular scratches, and a drill is hard to hold flat. A random orbital sander moves in an offset pattern that avoids those marks.
Drums are better than discs for curves and holes, and they work best in a drill press, where the drum stays square to the table.
Socket adapters
A socket adapter has a hex shank on one end and a square drive on the other, so a drill or impact driver can spin sockets. They come in 1/4, 3/8 and 1/2 in drive. They’re good for running nuts and lag bolts down quickly.
Don’t use one for final tightening when a bolt has a torque specification. A drill’s clutch doesn’t measure torque; use a torque wrench for the last turn. Types of torque wrenches explains which one to use.
Wire brushes and polishing pads
Wire brushes strip rust, scale and flaking paint from metal. Steel wire is aggressive; brass wire is gentler and won’t scratch softer metals as much. Wires break off in use, so wear goggles and gloves, and keep the brush moving so it doesn’t dig in.
Polishing pads restore car paint, headlights and metal. A drill can do it for small areas, though a dedicated polisher is easier to control on a whole car. Best cordless drill for polishing covers what to look for in a drill for this job.
Mixing paddles
Paddle mixers stir paint, joint compound and thinset in a bucket. Mixing thick material puts a heavy, steady load on the drill, so use a drill with a 1/2 in chuck and low speed, and stop if the motor gets hot. For bigger batches of concrete, see can you use a hammer drill to mix concrete.
Fitting attachments safely
- Tighten the shank fully in the chuck; a hex shank in a three-jaw chuck should sit on the flats. 1/2 in vs 3/8 in drill explains chuck sizes and what fits.
- Set the drill to its low speed gear for sanding drums, mixers and hole saws.
- Use the side handle and brace for kickback when a hole saw or mixer grabs.
- Never exceed the rpm marked on brushes, pads and abrasives.
Frequently asked questions
Is a drill sander attachment as good as a real sander?
For small jobs and shaping, yes. For large flat surfaces, a random orbital sander gives a far smoother, swirl-free finish and is easier to hold flat.
Can I use a socket adapter on an impact driver?
Only an impact-rated adapter. Standard chrome adapters can crack under impact. Impact adapters are usually black and made of tougher steel.
What speed should a wire brush run at?
Below the maximum rpm marked on the brush. Most drill-mounted brushes are rated well above a drill's top speed, but cheap brushes and large wheels may not be, so check the marking.
Related guides
- Guide
1/2 in vs 3/8 in Drill: Which Chuck Size Do You Need?
1/2-inch vs 3/8-inch drill: what the chuck size means, the largest bit each takes, torque and weight, and which suits DIY or heavy-duty work.
- Guide
Drill Guides and Drill Press Stands for a Hand Drill
How a drill guide or drill press stand helps a hand drill make straight, square and angled holes, which type to choose, and when you need a real drill press.
- Guide
Can a Hammer Drill Be Used as a Regular Drill?
Yes, a hammer drill works as a regular drill with the hammer action switched off. When it's a good substitute, when it isn't, and how to set it.