Roofing Nailers: Nail Length, Depth and What They Do

A roofing nailer is a coil nailer that fires wide-head roofing nails, typically 3/4 to 1-3/4 in long, quickly through shingles into the roof deck. Pick a nail long enough to go through the shingles and about 3/4 in into the deck, or all the way through thin sheathing, and set the depth so the head sits flush without cutting the shingle.

Roofing nailer at a glance

FeatureTypical value
Nail styleWide-head roofing nail, smooth or ring shank
Nail length3/4 to 1-3/4 in (19 to 44 mm)
CollationWire-welded coil, about 15°
CapacityOne coil, often 120 nails
PowerPneumatic (air compressor); some are cordless
Depth controlWheel or dial near the nose

The exact range depends on the model, so check the manual before you buy nails.

What a roofing nailer does

A roofing nailer shoots a nail every time you press the nose to the shingle and pull the trigger. The coil holds more nails than a stick magazine, which is why roofers use it: they can nail a large area without stopping to reload. The wide heads hold shingles down against wind. Many nailers also handle siding and fence nails, but only if the manual lists them.

Choosing nail length

  1. Count the layers: new shingles on bare decking need a shorter nail than a re-roof over old shingles.
  2. Measure the deck thickness. Nails should go about 3/4 in into the deck, or through it on thin sheathing.
  3. Pick the nail length that covers both: shingle thickness plus that 3/4 in. A 1-1/4 in nail suits one layer on standard decking, and longer nails suit a re-roof.
  4. Use nails recommended by the shingle maker, since the warranty and local code may set the type, such as galvanized or stainless, and the number per shingle.

Setting the depth

Set the depth so the head is flush with the shingle surface. A nail that is too proud lets the shingle lift, and one driven too deep cuts through it and loses holding. Fire a few nails into scrap shingle on a deck piece and adjust. Check again when the air pressure or temperature changes.

Roofing nailer vs framing nailer

A framing nailer fires large, round-head nails in plastic or paper strips at 21° or 30°, for studs and plates. A roofing nailer fires short wide-head nails from a coil. They are not interchangeable; for the other tool, see 21° vs 30° framing nailers, and for the full comparison of nailer types, see brad vs finish vs pin nailers.

Safety

Wear safety glasses and hearing protection. Keep your hand and body away from the nose, and don’t use the contact trip to bump-fire on the roof edge unless you are trained. Work with fall protection on a pitched roof and keep the air hose clear of your feet.

Frequently asked questions

What size nails does a roofing nailer use?

Roofing nails commonly run from 3/4 to 1-3/4 in long, in coils collated at about 15 degrees. Check the nailer's manual for the range it accepts.

How long should roofing nails be for shingles?

Long enough to go through the shingle layers and about 3/4 in into the roof deck, or through the deck if it is thinner. A 1-1/4 in nail is common for a single layer of shingles on 1/2 in decking.

Can I use a framing nailer for roofing?

No. A framing nailer fires larger nails with a different head and angle, and it is not made for shingles. A roofing nailer holds a coil of short, wide-head nails.

How do I set the depth on a roofing nailer?

Set it so the nail head sits flush with the shingle, neither raised nor sunk through it. Test on a scrap shingle and adjust the depth wheel.

Report a mistake on this page