Diamond Hole Saws: Tile, Glass and Stone
A diamond hole saw is a hollow cup with diamond grit on its rim that cuts round holes in hard, brittle materials such as porcelain tile, glass, granite and brick. Use it at slow speed with water on the cut. Common sizes run from about 1/4 in to 6 in, and the three main kinds are electroplated, vacuum-brazed and sintered.
Diamond hole saw types
| Type | How the diamond is attached | Best for | Notes |
|---|---|---|---|
| Electroplated | Grit plated onto the rim | Tile, glass, light use | Cheapest, wears faster |
| Vacuum-brazed | Grit brazed to the rim | Porcelain, granite, tougher work | Cuts faster, lasts longer, some can be used dry |
| Sintered | Diamond mixed into a metal rim | Stone, concrete, heavy work | Long life, costs more |
Makers vary, so check the label for the intended material and for wet or dry use.
What a diamond hole saw cuts
- Ceramic and porcelain tile, for pipe, tap and vent holes.
- Glass and mirrors; see how to drill glass.
- Granite and marble countertops; see drilling granite.
- Brick, block and concrete, in the sintered and heavy types.
For drilling a small hole in tile, a spear-point bit is often enough; see tile drill bits and diamond bits for porcelain tile.
Sizes
Diamond hole saws are sold by the outside diameter of the cup. Typical sizes run from about 1/4 in to 6 in. Pick the next size up from the pipe or fixture, and check the template for sink and faucet holes. A 4-1/4 in cup suits a 4 in pipe. For the standard sizes of ordinary hole saws, see hole saw sizes.
How to use a diamond hole saw
- Mark the hole on masking tape and clamp the work, or use a guide template to hold the saw in position.
- Fit the saw on the arbor, with the pilot bit if the saw takes one.
- Start at a slight angle to cut a groove, then bring the drill upright.
- Run at a slow speed, with water running or a dam of putty filled with water.
- Use light pressure and lift the saw now and then to clear slurry.
- Stop when the core is free, and lift it out gently.
Safety
Wear safety glasses and a dust mask when cutting stone, brick and concrete, because the dust contains silica. Keep power tools away from water, and use a ground-fault outlet or a cordless drill.
Frequently asked questions
Can a diamond hole saw cut tile?
Yes. It is one of the best ways to cut round holes in ceramic and porcelain tile, for pipes, taps and vents. Keep it wet and run it slowly.
Do I need water with a diamond hole saw?
Yes for most. Water cools the diamond grit and carries away dust. Some vacuum-brazed bits are made for dry use, but they still need short cuts and cooling.
What size diamond hole saw for a 4 in pipe?
Choose a hole saw slightly larger than the pipe diameter, for example 4-1/4 in for a 4 in pipe. Check the pipe's outside diameter and the fixture's template.
Is a diamond hole saw the same as a diamond core bit?
They are the same idea. A diamond core bit is the term often used for small sizes and for concrete, and a diamond hole saw for larger cups fitted on an arbor.
Related guides
- Guide
How to Drill Glass: Bottles, Mirrors and Glass Sheets
The bit to use for glass, how to start the hole, how to keep it cool, and how to drill bottles, mirrors and thick glass without cracking them.
- Guide
How to Sharpen a Drill Bit: Angles and Methods
How to tell a drill bit is dull, the 118° and 135° point angles, lip relief, and how to sharpen a twist bit by hand, on a grinder or with a sharpener.
- Guide
Step Drill Bits: Sizes, Uses and How to Use One
What a step drill bit is, common size ranges, which metals and plastics it drills, and how to use one for sheet metal and conduit knockout holes.